How to Use a Drill Press? | Step by Step Guideline

    How to Use a Drill Press!

    Drilling machines come in different sizes and shapes from the power drills to small hand-held. They can do several tasks that any DIY fun wishes to handle around the home. A drill press is one of the necessary woodworking tools that you may use for several projects.

    While you may use this drill press for making holes, it may also be fitted with a mortising attachment for making square holes. In this article, we share some steps on how to use a drill press.

    Step by Step Guide - How to Use a Drill Press

    Things to keep in mind

    • Before you start working on anything, you need to do the following.
    • Ensure that you unplug the machine
    • Read the instructions and follow them to the latter
    • The functions are not the same on every drill press

    Know your device

    • It is advisable that before you know how to use your machine you know its components. We decided to list them below before we explain the steps. Check out;
    • Power motor that features a half or two-inch horsepower
    • A chain of function on top of your machine for setting speed
    • Chuck that takes bits of different sizes
    • The arm is another part that rotates to increase and decrease the bit and chuck.
    • The table of drill press allows raising and lowering. It can also be taken out of the path or tilted to different angles to create space for huge tasks.

    Set up speed 

    When it comes to speed, most drill presses allow you to adjust it by shifting the drive to a different pulley. The pulley can rotate fast if the one on the toss axis is small. Just as it is with other cutting processes, the best speed for making a hole in metal is the lowest.

    If you are making holes in wood, consider setting faster speed. However, before deciding on the speed level, try to check the manual accompanying your machine. 

    Match the bit 

    There is no magic in fitting the bit. You need to open your chuck, move the drill use your hand to snug the chuck just about the shaft of the bit and tauten the three jaws of the chuck using the key. Ensure you remove the chuck because if you forget to remove it, it will end up being a risky projectile when you rotate the machine. While making huge holes, start by making a small, pilot hole.

    Fine-tune the table 

    Many drill press models have an oddball that regulates the height of the table while another slide in freely after the clamping lever has been set free. It is evident you have your preferred height you enjoy working with, set the height o-f the table for the process you wish to carry out.

    Measure the deepness 

    In case you are just making holes in some piece of the collection, there is no need to regulate the deepness range, the fiber rod that manages the space the spindle moves. But if you are worried regarding the halted opening of a fixed deepness, lessen the bit to the height of your preference.

    Then fine-tune the pair of knurled nuts on the deepness measurement to the right halting spot. Have one of the knurled bolts stopping the spindle while the other bolts the primary nut securely.

    Lock your workpiece 

    I know you are excited to start using your machine. But before you begin on operating the drill press, make sure that the work material you want to drill is secured in place. It is possible to the drill bit to attempt to rotate the metal or wood workpiece. 

    Therefore, ensure to hold tightly it to your worktable, supported against the holding column at the back of the drill press or have it secured. While you do- all these, ensure you do not handle the tool minus firmly attaching the working material. 

    Start making holes 

    After the setup process is complete, start to work with it simple. It is important to ensure that your drill is rotating at full speed. Place the drill to the work piece while lessening the bit by swaying the turning lever.

    After you complete making the hole, let go of the pressure on the arm. This will have its spring-loaded recoil system coming back to its original position. 

    • Sanding: If you are sanding uneven shapes, ensure to append a sanding flap controls to the fling. When sanding shapes that are regular, remember to fix a tap sander to your machine.
    • Circle cutting: When cutting a circle, ensure to fix the spherical reaper and secure the workpiece to the board. Put a scrap piece of wood on the bottom of the work parts. This is to avoid the circle reaper from damaging the board. Have the circle reaper stay firm by making holes in your working parts at a low pace.

    Take precautionary measures 

    As we said beforehand, it is vital to set your drill press at low pace when making a hole in the metal. This is due to the metal being solid stuff and therefore drilling it on high speed can cause the drill bit to suffer exhaustion. It is necessary to apply some drizzles of cutting grease to your metal ahead of your drilling project. 

    Here’s How to Use a Drill Press!


    Since you like crafting your things, having a drill press within your reach is imperative. A drill press is one of the tools that you can use to make holes, counter-bore, ream, as well as hit holes. With this machine, you can create holes of specified sizes in your material. It is also crucial to know that the size of your drill press determines how big the hole will be.

    This means, if your drill press is huge, it means you will make big openings. If you enjoyed reading this post, please tell us your views in the comments.

    About the Author Allen A

    Allen A. Jones is a specialized technician of electronic appliances. He has been working with Bestbuy since 2015 and helped thousands of customers to choose the right electronic gadgets offline. Now he is doing the exact same thing online. To know more about him, get in touch with him on Allen[at]

    follow me on:

    Leave a Comment: